Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
- 10. Brake system
   10.1. Technical data
   10.2. Prorolling of hydraulic brake system
   10.3. Brake pipelines and hoses
   10.4. Replacement of lobbies brake колодок
   10.5. Replacement back brake колодок
   10.6. Replacement back brake колодок on drum-type brakes
   10.7. A forward brake disk
   10.8. A back brake disk
   10.9. A back brake drum
   10.10. A support of a forward brake
   10.11. A support of a back wheel
   10.12. The back brake cylinder
   10.13. The main brake cylinder
   10.14. A brake pedal
   10.15. The vacuum amplifier of brakes
   10.16. The unilateral valve of the vacuum amplifier of brakes
   10.17. Adjustment of a manual brake
   10.18. The lever of a manual brake
   10.19. A cable of a manual brake
   10.20. Brake колодки a manual brake (model with disk brakes)
   10.21. The valve of adjustment of pressure in brake system
   10.22. The stoplight switch
   10.23. Antiblocking system of brakes (ABS)
   10.24. The vacuum pump (cars with the diesel engine)
   10.25. Check of the vacuum pump on cars with diesel engines
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

10.7. A forward brake disk

Check

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove a corresponding forward wheel.
2. Slowly turn a brake disk so that it could be considered from two parties. If necessary remove brake колодки. Deterioration of a brake disk from колодок should be in admissible limits. If deterioration exceeds an admissible limit or there are cracks on a disk, the disk is subject to replacement.
3. If necessary clear on perimetre a disk of a rust and a brake dust.
4. The indicator of hour type check up palpation of a brake disk. The indicator of hour type fix in any convenient place and, turning a disk, define its palpation in several points from its centre. If disk palpation exceeds admissible limits, the disk is subject to replacement. However failure of the bearing of a nave can be the reason of palpation of a disk.
5. For check of palpation of an inside of a brake disk remove a brake disk from a nave, turn it on 180 , repeatedly fix on a nave and by the indicator of hour type measure its palpation.
6. Check up a brake disk on presence of cracks, especially round apertures under bolts of fastening of a wheel.

Removal

PERFORMANCE ORDER
1. Unscrew two bolts of fastening of a support to a nave. Remove a support and, using a soft wire, adhere it to a forward rack. Thus do not deform and do not stretch a brake hose.
2. Using a chalk or a paint, note position of a brake disk concerning a nave.
3. Unscrew screws, крепящие a brake disk to a nave, and remove a disk.

Installation

PERFORMANCE ORDER
1. Installation is made in sequence, return to removal.
2. Consider following moments:
     – Check up that working surfaces of a brake disk and a nave pure and are not deformed;
     – Combine earlier made labels, establish a brake disk and fix screws, having tightened their demanded moment;
     – If the new brake disk, that is established, using solvent, clear it of protective greasing;
     – Before screwing up of bolts of fastening of a support a carving of bolts cover with means from unscrewing (Loctite Frenetanch);
     – Establish a wheel and lower the car;
     – Some times press a brake pedal that brake колодки were established into position.






course c++