Peugeot 406

Since 1996 of release

Repair and car operation

Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
- 10. Brake system
   10.1. Technical data
   10.2. Prorolling of hydraulic brake system
   10.3. Brake pipelines and hoses
   10.4. Replacement of lobbies brake колодок
   10.5. Replacement back brake колодок
   10.6. Replacement back brake колодок on drum-type brakes
   10.7. A forward brake disk
   10.8. A back brake disk
   10.9. A back brake drum
   10.10. A support of a forward brake
   10.11. A support of a back wheel
   10.12. The back brake cylinder
   10.13. The main brake cylinder
   10.14. A brake pedal
   10.15. The vacuum amplifier of brakes
   10.16. The unilateral valve of the vacuum amplifier of brakes
   10.17. Adjustment of a manual brake
   10.18. The lever of a manual brake
   10.19. A cable of a manual brake
   10.20. Brake колодки a manual brake (model with disk brakes)
   10.21. The valve of adjustment of pressure in brake system
   10.22. The stoplight switch
   10.23. Antiblocking system of brakes (ABS)
   10.24. The vacuum pump (cars with the diesel engine)
   10.25. Check of the vacuum pump on cars with diesel engines
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

10.4. Replacement of lobbies brake колодок

The prevention

Necessarily make replacement of all колодок on one axis of the car even if deterioration borders were reached by one колодка. If колодки will be repeatedly established, before removal they are necessary for marking.

At work brake колодок the brake dust which contains asbestos, unhealthy is formed. Therefore at clearing brake колодок do not use compressed air and do not inhale a dust.

1. Lift a forward part of the car and fix on supports. Remove forward wheels.
2. Disconnect the electric socket located on a wire, going to the gauge of deterioration brake колодок.
3. Press the piston into a support, displacing a support aside, opposite to a piston arrangement.
4. Unscrew a bolt of fastening of the bottom directing finger. Thus for deduction of a directing finger from проворачивания use a thin wrench. For fastening of a directing finger use only a new bolt.
5. Turn a support upwards on the top directing finger and tie up to a rack by means of a soft wire.
6. Take two brake колодки from the holder of a support.
7. Measure a thickness of an overlay of everyone brake колодки.
8. If the condition of overlays brake колодок supposes their further operation, clear them, using a pure wire brush and rags.
9. Before installation колодок check up, that directing fingers freely moved in the holder of a support, and be convinced that rubber protective covers of a directing finger are not damaged.
10. Clear a dust and a dirt from a support and the piston. Check up a condition of dustproof consolidation round the piston.
11. If will be established new brake колодки, press the piston into a support. It can be made a wooden core or the hammer handle. Thus especially watch, that the piston has not warped also surfaces of the piston and пыльника have not been damaged. At вдвигании the piston the brake liquid is superseded from the brake cylinder in a broad tank. Therefore constantly observe of liquid level in a tank and if necessary pump out it. At installation old brake колодок put them on the former places.
12. Insert external and internal brake колодки in the holder of a support.
13. Lower a support on brake колодки, passing a wire from the gauge of deterioration brake колодки through a window in a support. Grease a carving of a bolt of fastening of a directing finger with means against unscrewing (Peugeot recommends Loctite Frenetanch).
14. Press a support that it has occupied the position, then screw up a bolt of fastening of a directing finger, tightening its demanded moment.
15. Connect an electric socket of the gauge of deterioration brake колодки.
16. Check up level of a brake liquid in a tank. It should not exceed a mark "max". Some times press a brake pedal that колодки have nestled on a disk, and repeatedly check up level of a brake liquid in a tank.
17. Execute the actions set forth above on the second forward wheel.
18. Establish wheels and lower the car.
19. Repeatedly check up level of a brake liquid.