Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
- 5. Fuel system
   + 5.1. The power supply system of petrol engines
   - 5.2. Fuel system of diesel engines
      5.2.1. Technical data
      5.2.2. Filling and prorolling of fuel system
      5.2.3. The air filter and air inlet channels
      5.2.4. An accelerator cable
      5.2.5. An accelerator pedal
      5.2.6. Adjustment of the fuel pump of a high pressure
      5.2.7. The electromagnetic valve of a stop of the engine
      5.2.8. The fuel pump of high pressure Bosch
      5.2.9. The fuel pump of high pressure Lucas
      5.2.10. Installation of the moment of injection
      5.2.11. Installation of the moment of injection on ТНВД Bosch
      5.2.12. Installation of the moment of injection on ТНВД Lucas
      5.2.13. Fuel atomizers
      5.2.14. Gauges and executive mechanisms of system Bosch AS3
      5.2.15. Gauges and executive mechanisms (Lucas EPIC)
      5.2.16. An inlet collector
      5.2.17. A final collector
      5.2.18. Турбонагнетатель
      5.2.19. Removal and installation турбонагнетателя
      5.2.20. Check турбонагнетателя
      5.2.21. An intermediate cooler
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions



5.2.4. An accelerator cable

Removal

PERFORMANCE ORDER
1. On engines in volume of 1.9 litres remove a cable of an accelerator from a control lever of the fuel pump of a high pressure (it is specified by an arrow). Take a cover of a cable of an accelerator from the condensing ring established in a flange of the fuel pump.
2. On engines in volume of 2.1 litres take a cable of an accelerator from the lever on the gauge of position of management of the fuel giving, located on the left forward party of a motor compartment. Remove a cover of a cable of an accelerator from a gauge arm.
3. On all models take a cable of an accelerator from скоб fastenings in a motor compartment.
4. In car salon open a cover of an immobilizer and turn on 90 a clamp of a cover of a box with fuses. Disconnect an electric socket from колодки, unscrew screws of fastening and remove the bottom panel from outside the driver.
5. Remove скобу fastenings and disconnect a cable of an accelerator from the top part of a pedal of an accelerator.
6. Take a cover of a cable of an accelerator from a clamp on a suspension bracket of installation of a pedal, then to an accelerator cable adhere a long thin cord.
7. In a motor compartment take from a partition a ring condensing a cable of an accelerator, and take an accelerator cable. Untie from a cable of an accelerator a cord and leave it in a motor compartment. The cord is required for the subsequent tightening of a new cable of an accelerator into place.

Installation

PERFORMANCE ORDER
1. Adhere a cord to a new cable of an accelerator and, having pulled for a cable which is in salon of the car, stretch an accelerator cable through a partition. Untie a cord from an accelerator cable, establish a cable cover in a clamp of a suspension bracket of a pedal, and an accelerator cable connect to a pedal.
2. Check up that the accelerator cable is reliably fixed to a pedal then establish the bottom part of the panel.
3. In a motor compartment check up that the cover of a cable of an accelerator is correctly placed in a condensing ring in a partition, then place a cable on all length in скобах fastenings.
4. Pull a flat washer over a cover of a cable and establish in an arm. Connect a cable of an accelerator to the lever.

Adjustment

PERFORMANCE ORDER
1. Remove a clip of fastening of a cover of a cable of an accelerator. Check up, that the control lever was in the starting position and, moving a cable cover, choose sagging of a cable of an accelerator.
2. In the established position of a cable establish a fastening clip on an external flute of a cover of a cable before a rubber condensing ring and a washer. After clip and cable installation on the places insignificant sagging of a cable of an accelerator should be observed only. While the assistant smoothly presses an accelerator pedal, check up that the control lever completely turns and comes back in a starting position.