Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
- 5. Fuel system
   - 5.1. The power supply system of petrol engines
      5.1.1. Technical data
      5.1.2. The air filter and inlet channels
      5.1.3. An accelerator cable
      5.1.4. An accelerator pedal
      5.1.5. System of injection of fuel
      5.1.6. Pressure removal in fuel system
      5.1.7. The fuel pump
      5.1.8. A fuel tank
      5.1.9. Check of fuel system
      5.1.10. The case throttle заслонки
      5.1.11. System of injection Bosch Motronic MP511
      5.1.12. System of injection Magneti Marelli 8P
      5.1.13. An inlet collector
      5.1.14. A final collector
      5.1.15. System of release of the fulfilled gases
   + 5.2. Fuel system of diesel engines
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

5.1.9. Check of fuel system
THE GENERAL DATA

In the course of diagnostics at revealing of malfunctions each code of system corresponds to a certain element of system.

Reading of codes of malfunctions

Code
Malfunction
System of injection Motronic 5.1.1
11
Malfunctions are not found out
12
Malfunction installation
13
The gauge of temperature of soaked up air
14
The gauge of temperature of a cooling liquid
15
The relay of the fuel pump
21
The gauge of position of a potentiometer throttle заслонки – free contact
31
The free
32
Mix adjustment
33
The valve of the solenoid of the coal filter – damage кругооборота
34
The valve of the solenoid of the coal filter
35
The gauge of extreme position throttle заслонки
41
The gauge of turns of the engine and position коленвала
42
Atomizers
43
The detonation gauge
44
The detonation gauge – another
51
The ljambda-gauge
52
Regulation of structure of a mix
53
Pressure of the accumulator
54
Block ECU relay
56
Immobilizer
71
Check of injection of the cylinder № 1
72
Check of injection of the cylinder № 2
73
Check of injection of the cylinder № 3
74
Check of injection of the cylinder № 4
System of injection Magneti Marelli 8P
11
Malfunctions are not found out
12
Installation of malfunctions
13
The gauge of temperature of soaked up air
14
The gauge of temperature of a cooling liquid
15
The relay of the fuel pump
21
The gauge of position throttle заслонки
22
The engine of management of idling turns
27
The gauge of speed of the car
31
The ljambda-gauge
33
The pressure gauge in an inlet collector
34
The valve of the solenoid of the coal filter
41
The gauge of turns of the engine and position коленвала
42
Injector
44
The detonation gauge
45
The ignition coil
52
The ljambda-gauge
53
Pressure of the accumulator
54
Block ECU
57
The ignition coil

Check

PERFORMANCE ORDER
1. Check up reliability of connection of wires and absence of corrosion.
2. Check up a condition of the air filter and свеч ignitions. Check up pressure of a compression in engine cylinders.
3. If the elementary check does not possible to find out a cause of defect, it can be written down in memory of system ECU.
4. For malfunction definition it is necessary to connect the special diagnostic equipment to system ECU.