Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
- 5. Fuel system
   - 5.1. The power supply system of petrol engines
      5.1.1. Technical data
      5.1.2. The air filter and inlet channels
      5.1.3. An accelerator cable
      5.1.4. An accelerator pedal
      5.1.5. System of injection of fuel
      5.1.6. Pressure removal in fuel system
      5.1.7. The fuel pump
      5.1.8. A fuel tank
      5.1.9. Check of fuel system
      5.1.10. The case throttle заслонки
      5.1.11. System of injection Bosch Motronic MP511
      5.1.12. System of injection Magneti Marelli 8P
      5.1.13. An inlet collector
      5.1.14. A final collector
      5.1.15. System of release of the fulfilled gases
   + 5.2. Fuel system of diesel engines
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

5.1.3. An accelerator cable

Removal

PERFORMANCE ORDER
1. In a motor compartment remove a cable of an accelerator from a cam on the case of throttles, then take a cover of a cable of an accelerator from a condensing rubber ring (the arrow specifies a clip of an external cover of a cable of an accelerator).
2. Release an accelerator cable on all length from скоб fastenings.
3. In car salon open a cover of an immobilizer and turn on 90 a clamp of a cover of a box with fuses.
4. Disconnect an electric socket from колодки, unscrew screws of fastening and remove the bottom panel from outside the driver.
5. Remove скобу fastenings and disconnect a cable of an accelerator from the top part of a pedal of an accelerator.
6. Take a cover of a cable of an accelerator from a clamp on a suspension bracket of installation of a pedal, then to an accelerator cable adhere a long thin cord.
7. In a motor compartment take from a partition a ring condensing a cable of an accelerator and take an accelerator cable.
8. Untie from a cable of an accelerator a cord and leave it in a motor compartment. The cord is required for the subsequent tightening of a new cable of an accelerator into place.

Installation

PERFORMANCE ORDER
1. Adhere a cord to a new cable of an accelerator. Having pulled for a cable which is in salon of the car, stretch an accelerator cable through a partition.
2. Untie a cord from an accelerator cable, establish a cable cover in a clamp of a suspension bracket of a pedal, and an accelerator cable connect to a pedal.
3. Check up that the accelerator cable is reliably fixed to a pedal then establish the bottom part of the panel.
4. In a motor compartment check up that the cover of a cable of an accelerator is correctly placed in a condensing ring in a partition, then place a cable on all length in скобах fastenings.
5. Pull a flat washer over a cover of a cable both establish in an arm and connect a cable of an accelerator to a throttle cam.

Adjustment

PERFORMANCE ORDER
1. Remove a clip of fastening of a cover of a cable of an accelerator. Check up, that the throttle cam was in the starting position and moving a cable cover, choose sagging of a cable of an accelerator.
2. In the established position of a cable establish a fastening clip on an external flute to a cable cover before a rubber condensing ring and a washer.
3. After clip and cable installation on the places insignificant sagging of a cable of an accelerator should be observed only. While the assistant smoothly presses an accelerator pedal, check up that the throttle cam completely turns and comes back in a starting position.