Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
- 4. Systems of cooling, heating and ventilation
   4.1. Technical data
   4.2. Connection of hoses of system of cooling
   4.3. A radiator
   4.4. The thermostat
   4.5. The electric fan
   4.6. Temperature-sensitive elements
   4.7. The gauge of a lamp of excess of temperature of a cooling liquid
   4.8. The water pump
   4.9. A heating system and ventilation
   4.10. Elements of system of heating
   4.11. Air central airs
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

4.10. Elements of system of heating THE MANAGEMENT BLOCK

Removal

PERFORMANCE ORDER
1. Disconnect the negative plug of the accumulator.
2. Unscrew fastening screws (are specified by arrows) and take the block of management from the panel.
3. From the back party of the block of management release clips and disconnect cables of management from the block.
4. Disconnect from the block electric sockets and completely remove the management block.

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Check up, that management cable were established strictly on the places. Check up work of the block of management before installation to the place of a radio receiver.

MANAGEMENT CABLES

Removal

PERFORMANCE ORDER
1. Remove cables of management from the management block.
2. Working through an aperture in the panel or under the panel disconnect скобы and a corresponding cable from a heater.

Installation

PERFORMANCE ORDER
Installation is made in sequence, return to removal. Check up, that management cables have been correctly placed.

HEATER RADIATOR


The prevention

At installation to the place of a heater radiator new sealing rings should be used.


Removal

PERFORMANCE ORDER
1. Merge cooling liquid from cooling system. Serially press hoses of a supply of a cooling liquid to a radiator of a heater near a partition of a motor compartment.
2. Remove a steering column. Unscrew bolts of fastening and remove a suspension bracket of support of the panel for the best access to a heater radiator.
3. Establish the corresponding container under a heater radiator. Unscrew a bolt of fastening and remove pipes of a supply of a cooling liquid to a radiator. Wait, while the rests of a cooling liquid will not flow down in the container.
4. Unscrew bolts of fastening of pipes.
5. Replace ring consolidations (are specified by arrows) on the ends of pipes.
6. Unscrew fastening bolts (are specified by arrows) a radiator of a heater and put forward it from a nest.

Installation

PERFORMANCE ORDER
Installation is made in sequence of return to removal, considering following moments:
      – Establish new ring consolidations on pipes;
      – Move a heater radiator into place and connect to pipes. Remove clips from hoses;
      – Fill system of cooling with a cooling liquid.

THE ENGINE OF THE FAN OF THE HEATER

Removal

PERFORMANCE ORDER
1. The engine of the fan of a heater is located on the right side under the forward panel.
2. Disconnect the negative plug of the accumulator. Remove скобы fastenings from the panel basis from outside the passenger. If necessary remove a ware box.
3. Remove an electric socket from the engine and take a plait of wires from скобы.
4. Unscrew bolts of fastening of the engine and take the fan from a casing.

Installation

Installation is made in sequence, return to removal.

THE BLOCK OF ENGINE MANAGEMENT OF THE FAN OF THE HEATER

Removal

PERFORMANCE ORDER
1. Remove the heater fan.
2. Take condensing ring of a plait of wires from the fan basis. Disconnect a socket from the fan and remove a plait of wires.
3. Disconnect скобы fastenings (arrow) and separate the engine from a cover.
4. Unscrew screws of fastening (arrow) and remove the block of engine management from a cover.

Installation

Installation is made in sequence, return to removal.