Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. The engine
   + 3.1. Petrol engines
   + 3.2. Diesel engines
   - 3.3. Engine repair
      3.3.1. Technical data
      3.3.2. Removal and engine and transmission installation
      3.3.3. Removal and installation of engines from an automatic transmission
      3.3.4. Engine repair
      3.3.5. Removal and installation of a head of the block of cylinders
      3.3.6. Dismantling of a head of the block of cylinders
      3.3.7. Clearing and survey of a head of the block of cylinders
      3.3.8. Assemblage of a head of the block of cylinders
      3.3.9. Removal of pistons from rods
      3.3.10. Removal коленвала
      3.3.11. The block of cylinders
      3.3.12. Pistons and rods
      3.3.13. Коленвал
      3.3.14. Survey radical and шатунных bearings
      3.3.15. Engine balance of assembly at major repairs
      3.3.16. Installation of piston rings
      + 3.3.17. Installation коленвала and check of working backlashes of radical bearings
      - 3.3.18. Installation of pistons
         3.3.18.1. A choice of the loose leaf of the bearing
         3.3.18.2. Check of a working backlash of the loose leaf шатунного the bearing
      3.3.19. Start of the engine after major repairs
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

3.3.18.2. Check of a working backlash of the loose leaf шатунного the bearing
PERFORMANCE ORDER
1. Clear шатунные loose leaves and their nests. The working backlash can be checked up two methods.
2. One of methods (which presence of a micrometer for measurement of diameter of apertures assumes) consists in establishing covers шатунных bearings together with the loose leaf on a rod and to screw their demanded moment. At loose leaf installation in a rod the ledge on the loose leaf (marksman) should be established in a groove on a rod.
3. Measure internal diameter of each collected pair loose leaves of the bearing. Measure diameter of everyone шатунной necks коленвала. Subtract from the measured diameter of the bearing the corresponding diameter шатунной necks коленвала.
4. The second (and more exact method) consists in using a product known as Plastigage. It is a round plastic core which is compressed between the loose leaf and a neck коленвала. After cover removal шатунного the bearing the deformed plastic core is measured by a special template which is available in complete set Plastigage. Procedure for use Plastigage the following.
5. Establish a rod with the loose leaf on a corresponding neck коленвала. Necks коленвала and loose leaves should be absolutely pure and dry.
6. Cut off a slice of plastic core Plastigage (it should be slightly shorter, than width шатунных bearings) and establish it on a measured neck коленвала.
7. Establish шатунные covers with the bottom loose leaves and tighten bolts of fastening by the demanded moment. In the course of measurement of a backlash by method Plastigage do not rotate коленвал.
8. Unscrew шатунную a cover of fastening of the loose leaf, remove it and to the deformed plastic core put the scale ruler printed on packing. Comparing width of the deformed plastic core with control width on a scale ruler, define backlash size.
9. In end carefully clear traces Plastigage of a material from loose leaves and коленвала.