Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
- 3. The engine
   - 3.1. Petrol engines
      3.1.1. Technical data
      3.1.2. Check of pressure of compression
      3.1.3. Mechanism installation timing
      3.1.4. A cover of a head of the block of cylinders
      3.1.5. A pulley of a cranked shaft
      3.1.6. A casing of a gear belt
      3.1.7. A gear belt
      3.1.8. The mechanism of a tension of a gear belt and pulleys
      3.1.9. Replacement of a sealing ring of a cam-shaft
      3.1.10. A cam-shaft and pushers
      3.1.11. Check and adjustment of backlashes of valves of engines of 1.6 litres
      3.1.12. A head of the block of cylinders
      3.1.13. The oil pallet
      3.1.14. The oil pump
      3.1.15. An oil radiator
      3.1.16. Replacement of consolidations of a cranked shaft
      3.1.17. A flywheel
      3.1.18. A suspension bracket of the power unit
   + 3.2. Diesel engines
   + 3.3. Engine repair
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

3.1.13. The oil pallet Removal

PERFORMANCE ORDER
1. Disconnect the negative plug from the accumulator.
2. Fix back wheels, понимите a forward part of the car and fix it on supports.
3. Merge engine oil.
4. At presence remove a socket from the gauge of temperature of oil which is screwed in in the oil pallet.
5. Remove auxiliary приводной a belt.
6. On models with the conditioner unscrew a bolt of fastening of the compressor to the pallet and a soft wire fix the compressor on a body.
7. Gradually ослабьте also unscrew bolts of fastening of the pallet. Since bolts of fastening of the pallet have different length, it is necessary to spread out them so that at installation they have risen on the places.
8. Palm blows separate the oil pallet from the block of cylinders. In the presence of a lining remove it. At pallet installation use only a new lining. At the removed pallet check up the oil pump and a grid маслоприемника.
9. On some models of engines the plate between the pallet and the block of cylinders is established. If it is necessary to remove a plate, unscrew two bolts of fastening which are located in диагонально opposite corners of a plate.

Installation

PERFORMANCE ORDER
1. Carefully clear the lining rests on interfaced surfaces of the oil pallet and the block of cylinders.
2. In the presence of a plate between the pallet and the block of cylinders clear from it the rests of a lining and cover the top part of a plate with hermetic. Establish a plate on the block of cylinders and tighten fastening bolts.
3. On models where the oil pallet is established directly on the block of cylinders, clear interfaced surfaces and grease with a thin layer of hermetic.
4. On models where the pallet is established with a lining, check up that traces of an old lining are removed, and interfaced surfaces dry and pure. Establish a new lining on the pallet.
5. Establish the pallet on the block of cylinders of the engine both in regular intervals and consistently tighten its bolts.
6. On models with the conditioner screw on the pallet the compressor.
7. Establish auxiliary приводной a belt and a pressure regulator.
8. Connect an electric socket to the gauge of temperature of oil.
9. Lower the car, fill in in the engine oil and connect the negative plug to the accumulator.