Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
- 13. An electric equipment
   13.1. Technical data
   13.2. Detection of not closed chain
   13.3. Safety locks and the relay
   13.4. Switches
   13.5. Bulbs of external illumination
   13.6. Lamps of illumination of salon
   13.7. Devices of external illumination
   13.8. Adjustment of light of headlights
   13.9. A combination of devices
   13.10. The multipurpose display
   13.11. Прикуриватель
   13.12. Hours
   13.13. A sound signal
   13.14. The screen wiper lever
   13.15. The screen wiper and draught engine
   13.16. A back screen wiper
   13.17. Стеклоомыватель
   13.18. An automobile radio tape recorder
   13.19. A column (dynamics)
   13.20. The aerial
   13.21. A cruise-control control system
   13.22. Anticreeping system and an engine immobilizer
   13.23. Electric units of forward sitting
   13.24. A safety pillow
   13.25. Elements of a pillow of safety
   + 13.26. Electric schemes
+ 14. The basic malfunctions

13.7. Devices of external illumination
THE GENERAL DATA

The prevention

Before removal of devices of illumination remove the negative plug from the accumulator.


Removal and installation

HEADLIGHTS

PERFORMANCE ORDER
1. Open a cowl and remove connectors of fastening of a lattice of a radiator.
2. By means of a screw-driver disconnect скобы fastenings and remove a lattice.
3. Unscrew nuts of fastening of a casing of the fan to the cowl lock. Unscrew bolts (fastenings of the lock of a cowl are specified by arrows) and disconnect from it a cable.
4. Disconnect a cable from the lock of a cowl and remove the lock.
5. From under an arch of a wheel by means of a small screw-driver remove заглушку for access to a spring of fixing of a headlight.
6. By means of flat-nose pliers or a special core disconnect a spring of fixing of a headlight to a car body.
7. Unscrew 3 bolts of fastening of a headlight.
8. Disconnect an electric socket (a photo at the left) and take a headlight (a photo on the right).
9. On the cars equipped with the proof-reader of light of headlights, remove the engine of the proof-reader from a back part of a headlight, turning it counter-clockwise.
10. Being careful, disconnect the spherical hinge from a back part of a reflector of a headlight.
11. Installation is made in sequence, return to removal.

ANTIFOG HEADLIGHT

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Unscrew screws and remove plastic protection from the bottom part of an antifog headlight.
2. Disconnect an electric socket and unscrew the bottom screw of fastening of a headlight.
3. Disconnect the top fixing spring and take a headlight from the bottom forward part of a bumper.
4. Installation is made in sequence, return to removal.
5. For adjustment of light of an antifog headlight, using a special key, turn a regulator on a back part of a headlight. If the plastic sheeting of the bottom part of a headlight is removed, the regulator of light of a headlight can be turned a hand.

BACK LANTERN ON MODELS THE SEDAN (SALOON)

PERFORMANCE ORDER
1. Unscrew screws of fastening and remove back furnish of a luggage carrier. Take percussion caps and remove a back upholstery of a luggage carrier. On some models for access to the left back lantern unscrew a clip and remove storage branch.
2. Release скобы and disconnect an electric socket from a back lantern.
3. Unscrew nuts (a photo at the left) and remove a back lantern (a photo on the right).
4. Installation is made in sequence, return to removal.

BACK LANTERN ON CAR KOMBI WING (ESTATE)

PERFORMANCE ORDER
1. Uncover storage branches in a luggage compartment.
2. Remove скобу fastenings, disconnect an electric socket, unscrew a nut (it is specified by an arrow) fastenings and remove a back lantern from a car wing.
3. Installation is made in sequence, return to removal.

THE BACK LANTERN LOCATED ON THE BACK DOOR OF CARS KOMBI (ESTATE)

PERFORMANCE ORDER
1. Open a back door and remove from it an upholstery.
2. Release скобу and disconnect an electric socket. Unscrew nuts (fastenings are specified by arrows in a photo at the left) and remove a back lantern from a back door.
3. Installation is made in sequence, return to removal.

ADDITIONAL TOP STOPLIGHTS

PERFORMANCE ORDER
Models a sedan (Saloon)
1. Using the bent core, insert it into lantern clamps, release скобы fastenings and pull a lantern downwards.
2. Shift a lantern back, release from directing, take from the car and disconnect an electric socket.
3. Installation is made in sequence, return to removal.
Models комби (Estate)
4. Open a back door and remove screws (are specified by arrows) fastenings of a spoiler from the top part of a door.
5. Remove a spoiler, disconnect an electric socket (1) and a hose (2) washers of back glass and take them from a back door (3 – screws of fastening of an additional sling-signal and a spoiler).
6. Installation is made in sequence, return to removal.

LANTERN OF ILLUMINATION OF LICENSE PLATE


PERFORMANCE ORDER
Models a sedan (Saloon)
1. Take a lantern of illumination of licence plate from a back bumper (a photo at the left) and disconnect an electric socket (a photo on the right).
2. Installation is made in sequence, return to removal.
Models комби (Estate)
3. Open a back door, unscrew screws and remove the internal handle. Remove a decorative overlay of the internal button of the lock. Remove furnish of a back door.
4. Disconnect an electric socket from a back part of a lantern (a photo at the left) and take a lantern from a back door (a photo on the right).
5. Installation is made in sequence, return to removal.






honeynow.ru