Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
- 13. An electric equipment
   13.1. Technical data
   13.2. Detection of not closed chain
   13.3. Safety locks and the relay
   13.4. Switches
   13.5. Bulbs of external illumination
   13.6. Lamps of illumination of salon
   13.7. Devices of external illumination
   13.8. Adjustment of light of headlights
   13.9. A combination of devices
   13.10. The multipurpose display
   13.11. Прикуриватель
   13.12. Hours
   13.13. A sound signal
   13.14. The screen wiper lever
   13.15. The screen wiper and draught engine
   13.16. A back screen wiper
   13.17. Стеклоомыватель
   13.18. An automobile radio tape recorder
   13.19. A column (dynamics)
   13.20. The aerial
   13.21. A cruise-control control system
   13.22. Anticreeping system and an engine immobilizer
   13.23. Electric units of forward sitting
   13.24. A safety pillow
   13.25. Elements of a pillow of safety
   + 13.26. Electric schemes
+ 14. The basic malfunctions

13.5. Bulbs of external illumination

Replacement


The prevention

Before replacement of bulbs of external illumination check up a corresponding electric chain and a safety lock.

Do not concern a glass flask of a lamp with hands. The fingerprint evaporates and besieged on a reflector therefore illumination worsens. Necessarily replace the failed lamps with lamps of the same type. Stains arising on imprudence from a touch wipe pure безворсовой a rag or spirit.


HEADLIGHT

PERFORMANCE ORDER
1. Release скобы fastenings and uncover a back part of a headlight.
2. Remove an electric socket from a back part of a lamp накаливания headlights.
3. Compress spring скобы fastenings of a bulb and cast away them aside. Take a bulb from a headlight.
4. Establish a new bulb so that ledges on a bulb cartridge were combined with headlight grooves, and fix a bulb spring скобами.
5. Connect an electric socket and establish a back cover of a headlight.

FORWARD DIMENSIONAL FIRE

PERFORMANCE ORDER
1. Release скобу fastenings and remove a back cover from a headlight.
2. Turn a cartridge of a dimensional lantern and take it from a headlight. Take a bulb from a cartridge, having pulled it on itself.
3. Installation is made in sequence, return to removal.

ANTIFOG HEADLIGHTS

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports.
2. Unscrew screws (are specified by arrows) and remove the plastic mudguard located under an antifog headlight.
3. Disconnect an electric socket (a photo at the left), release скобу fastenings and remove an antifog headlight (a photo on the right).
4. Disconnect a spring clip (it is specified by an arrow) and take a reflector from the headlight case.
5. Disconnect an electric socket (it is specified by an arrow in a photo at the left), compress a spring of fastening of a bulb and take a bulb from a headlight (a photo on the right).
6. Establish a new bulb so that ledges on a bulb cartridge were combined with headlight grooves, and fix spring скобой.
7. Connect an electric socket and spring скобу reflector fastenings in a headlight.
8. Establish a headlight into place and fix скобой fastenings.
9. Connect an electric socket and establish into place plastic mudguards under a headlight.

THE FORWARD INDEX OF TURN

PERFORMANCE ORDER
1. For access improvement to the forward left index of turn remove a protective cover from the accumulator.
2. Turn a cartridge of a bulb of the forward index of turn counter-clockwise and take it from a back part of the index of turn. For lamp extraction накаливания from a cartridge press it and in this position turn on or counter-clockwise.
3. Installation is made in sequence, return to removal.

THE LATERAL REPEATER OF TURN

PERFORMANCE ORDER
1. By means of a screw-driver take the lateral repeater of turn from a car wing.
2. Turn a cartridge with a bulb counter-clockwise and take it. For extraction of a bulb from a cartridge pull it on itself.
3. Installation is made in sequence, return to removal.

BULBS OF THE BACK LANTERN

PERFORMANCE ORDER
1. In a back part of a luggage space unscrew screws and remove back furnish of a luggage carrier. Take percussion caps and remove a back upholstery of a luggage carrier.
2. On some models for access to the left back lantern unscrew a connector (it is specified by an arrow in a photo at the left), remove branch of storage and turn on aside the left lateral furnish of a luggage carrier (a photo on the right).
3. Release clamps and take a cartridge with a bulb from a back lantern.
4. For extraction of a bulb from a cartridge press it and in this position turn counter-clockwise.
5. Installation is made in sequence, return to removal.

BULBS OF THE BACK LANTERN ON MODELS КОМБИ (ESTATE)


PERFORMANCE ORDER
1. Remove a back lantern.
2. Release clamps and remove the holder of bulbs from a back lantern.
3. For extraction of a bulb from the holder of a back lantern press it and in this position turn counter-clockwise.
4. Installation is made in sequence, return to removal.

BULB OF ILLUMINATION OF LICENSE PLATE ON MODELS THE SEDAN (SALOON)

PERFORMANCE ORDER
1. Release скобу fastenings and remove a plafond from a lantern of illumination of licence plate.
2. Take a bulb from the holder, having pulled it on itself.
3. Installation is made in sequence, return to removal.

BULB OF ILLUMINATION OF LICENSE PLATE ON MODELS КОМБИ (ESTATE)

PERFORMANCE ORDER
1. Unscrew the screw and remove a plafond of a lantern of illumination of licence plate.
2. Remove a bulb, having pulled it on itself.
3. Installation is made in sequence, return to removal.