Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. A suspension bracket and a steering
+ 12. A body
- 13. An electric equipment
13.1. Technical data
13.2. Detection of not closed chain
13.3. Safety locks and the relay
13.4. Switches
13.5. Bulbs of external illumination
13.6. Lamps of illumination of salon
13.7. Devices of external illumination
13.8. Adjustment of light of headlights
13.9. A combination of devices
13.10. The multipurpose display
13.11. Прикуриватель
13.12. Hours
13.13. A sound signal
13.14. The screen wiper lever
13.15. The screen wiper and draught engine
13.16. A back screen wiper
13.17. Стеклоомыватель
13.18. An automobile radio tape recorder
13.19. A column (dynamics)
13.20. The aerial
13.21. A cruise-control control system
13.22. Anticreeping system and an engine immobilizer
13.23. Electric units of forward sitting
13.24. A safety pillow
13.25. Elements of a pillow of safety
+ 13.26. Electric schemes
+ 14. The basic malfunctions
|
The prevention Before removal of any switch remove the negative plug from the accumulator.
Removal and installation
THE SWITCH OF THE STEERING COLUMN
| PERFORMANCE ORDER |
| 1. Unscrew screws of fastening of the bottom casing of a steering column and remove the top and bottom casings from a steering column. Disconnect an electric socket from the cruise-control. |
|
|
| 2. Disconnect an electric socket from the switch, unscrew fastening screws (are specified by arrows in a photo at the left) and take the switch from a steering column (a photo on the right). |
| |
3. Installation is made in sequence, return to removal (fastening screws are specified by arrows). |
|
THE CRUISE-CONTROL SWITCH
| PERFORMANCE ORDER |
| 1. Unscrew screws of fastening of the bottom casing of a steering column, disconnect an electric socket and remove the bottom casing. |
|
|
2. Unscrew fastening screws (are specified by arrows) and remove the switch of the cruise-control from the bottom casing of a steering column. |
| 3. Installation is made in sequence, return to removal. |
|
SWITCHES OF THE PANEL OF DEVICES
| PERFORMANCE ORDER |
| 1. Open an immobilizer cover, turn a clip on 90 and uncover boxes with fuses. |
|
|
2. Unscrew screws (are specified by arrows) fastenings of the basis of group of switches. |
| |
3. Remove group of switches from the panel of devices and disconnect an electric socket. |
|
4. For removal of the separate switch from group of switches wring out скобы blockings and remove the switch. |
| 5. Installation is made in sequence, return to removal. |
|
SWITCHES OF THE CENTRAL PART OF THE PANEL OF DEVICES
| PERFORMANCE ORDER |
| 1. Remove the multipurpose display. On cars without the display separate the right party of the switch by means of a thin screw-driver from outside a ware box. |
|
|
2. Remove a frame of switches. |
| |
3. Unscrew screws (fastenings are specified by arrows) and remove group of switches from the panel of devices. |
|
4. Disconnect electric sockets and remove each switch separately from others. |
| 5. Installation is made in sequence, return to removal. |
|
SWITCHES OF THE CENTRAL CONSOLE
| PERFORMANCE ORDER |
| The switch of the central console can be taken from a nest after the central console will be unscrewed from a car floor. |
|
GROUP OF SWITCHES ON THE DOOR
| PERFORMANCE ORDER |
|
|
1. By means of a thin screw-driver remove a decorative overlay of switches on a car door. |
|
|
| 2. By means of the lever take the switch from a nest on a door (a photo at the left) and disconnect from it an electric socket (a photo on the right). |
| 3. Installation is made in sequence, return to removal. |
|
SWITCHES OF THE TOP CONSOLE
| PERFORMANCE ORDER |
|
|
1. Uncover a back part of the top console. |
|
|
2. Unscrew 2 screws (fastenings are specified by arrows) and lower downwards the top console. |
| |
3. Disconnect electric sockets and take the top console from the car. |
|
|
| 4. For removal of the switch of the hatch unscrew screws (fastenings of the printed-circuit board are specified by arrows in a photo at the left) and take the switch from top (a photo on the right). Other switches are a component of the top console and cannot separately be replaced. |
| 5. Installation is made in sequence, return to removal. |
|
SWITCHES OF SEATS
| PERFORMANCE ORDER |
| 1. Being careful, by means of the lever take the switch from a lateral bottom part of a seat and disconnect from it an electric socket. |
| 2. Connect to the switch an electric socket and establish it into place. |
|
THE SWITCH OF THE CONTROL LAMP OF INCLUSION OF THE MANUAL BRAKE
| PERFORMANCE ORDER |
| 1. Remove the central console. |
| 2. Disconnect an electric socket from the switch of a control lamp of inclusion of a manual brake, disconnect the switch and remove from the lever of a manual brake. |
| 3. Installation is made in sequence, return to removal. |
|
THE SWITCH OF ILLUMINATION OF SALON
| PERFORMANCE ORDER |
|
|
1. Open a door and remove a rubber cover from the switch located on a rack of a door. |
| |
2. Release clamps and being careful take the switch from a rack. |
| |
3. Disconnect from it an electric socket, adhere to the wires going to the switch, a thin cord. |
| 4. Installation is made in sequence, return to removal. |
|
THE SWITCH OF ILLUMINATION OF THE LUGGAGE CARRIER
| PERFORMANCE ORDER |
| 1. On cars a sedan (Saloon) open a luggage carrier cover, take percussion caps and remove luggage carrier furnish. |
| 2. On models комби (Estate) open a back door, unscrew screws and remove the internal handle of a back door. Using a thin screw-driver, remove decorative furnish of the internal button of the lock. |
|
|
3. Unscrew bolts, remove the switch and disconnect from it an electric socket. |
| 4. Installation is made in sequence, return to removal. |
|
THE GAUGE OF THE RAIN OF THE SCREEN WIPER
| PERFORMANCE ORDER |
| 1. Remove the case of an internal rear-view mirror from the interior of a windshield, having pulled it downwards. |
| 2. Disconnect an electric socket, disconnect скобы fastenings and remove the gauge of a rain from a windshield. |
The prevention Do not concern with hands of a lens of the gauge of a rain or a windscreen in the field of gauge installation since for normal work of the gauge its lens and a windscreen should be absolutely pure.
|
| 3. Installation is made in sequence, return to removal. |
|
|
|