Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. A suspension bracket and a steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward bearings of a nave
   11.4. A forward rack
   11.5. Repair of a forward rack
   11.6. The bottom lever of a forward suspension bracket
   11.7. The bottom spherical hinge of a forward suspension bracket
   11.8. The stabilizer of cross-section stability of a forward suspension bracket
   11.9. A side scene of the stabilizer of cross-section stability of a forward suspension bracket
   11.10. The bottom frame of a forward suspension bracket
   11.11. A nave of a back wheel
   11.12. Replacement of bearings of a back nave
   11.13. The shock-absorber of a back suspension bracket
   11.14. A cylindrical spring of a back suspension bracket
   11.15. A pin of a nave of a back suspension bracket
   11.16. The bottom lever of a back suspension bracket
   11.17. The top lever of a back suspension bracket
   11.18. The directing lever of a back suspension bracket
   11.19. Draught of a back suspension bracket
   11.20. The stabilizer of cross-section stability of a back suspension bracket
   11.21. A side scene of the stabilizer of cross-section stability of a back suspension bracket
   11.22. A steering wheel
   11.23. A steering column
   11.24. An intermediate shaft of a steering column
   11.25. The ignition lock
   11.26. The steering mechanism
   11.27. Replacement of protective covers of the steering mechanism
   11.28. Removal of air from system of a steering with the amplifier
   11.29. The pump of the amplifier of a steering
   11.30. The spherical hinge of steering draught
   11.31. Steering draught
   11.32. Corners of installation of wheels
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

11.30. The spherical hinge of steering draught Removal

PERFORMANCE ORDER
1. Lift a forward part of the car and fix on supports. Remove a corresponding forward wheel.
2. Using чертилку, note position of the spherical hinge on steering draught.
3. Fix steering draught and unscrew a counternut of the spherical hinge on a turn quarter. Do not move a counternut from this position as it will serve as a reference point at installation of the new spherical hinge.
4. Unscrew a nut of fastening of the spherical hinge to a rotary fist.
5. Remove the spherical hinge from a rotary fist.
6. Screw together the spherical hinge from steering draught, having counted exact number of turns of the spherical hinge.
7. Count number of full coils of a carving between the end of the spherical hinge and a counternut. If it is necessary to establish the new spherical hinge, screw together from the old hinge a counternut.
8. Carefully clear the spherical hinge and its carving. If the hinge has люфт or its protective cover is damaged, it is necessary to replace it.

Installation

PERFORMANCE ORDER
1. If the new spherical hinge of steering draught is established, screw on it a counternut on that quantity of coils which was on the old spherical hinge at removal.
2. Screw up the spherical hinge in steering draught on the same number of turns, as at removal. Thus, the counternut on the hinge should be established on a quarter of a turn from steering draught.
3. Establish a pin of the spherical hinge in a rotary fist, fix a new nut and tighten its demanded moment.
4. Establish a wheel and lower the car.
5. Check up and, if necessary, adjust corners of installation of forward wheels. After that tighten a counternut of the spherical hinge of steering draught.