Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. A suspension bracket and a steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward bearings of a nave
   11.4. A forward rack
   11.5. Repair of a forward rack
   11.6. The bottom lever of a forward suspension bracket
   11.7. The bottom spherical hinge of a forward suspension bracket
   11.8. The stabilizer of cross-section stability of a forward suspension bracket
   11.9. A side scene of the stabilizer of cross-section stability of a forward suspension bracket
   11.10. The bottom frame of a forward suspension bracket
   11.11. A nave of a back wheel
   11.12. Replacement of bearings of a back nave
   11.13. The shock-absorber of a back suspension bracket
   11.14. A cylindrical spring of a back suspension bracket
   11.15. A pin of a nave of a back suspension bracket
   11.16. The bottom lever of a back suspension bracket
   11.17. The top lever of a back suspension bracket
   11.18. The directing lever of a back suspension bracket
   11.19. Draught of a back suspension bracket
   11.20. The stabilizer of cross-section stability of a back suspension bracket
   11.21. A side scene of the stabilizer of cross-section stability of a back suspension bracket
   11.22. A steering wheel
   11.23. A steering column
   11.24. An intermediate shaft of a steering column
   11.25. The ignition lock
   11.26. The steering mechanism
   11.27. Replacement of protective covers of the steering mechanism
   11.28. Removal of air from system of a steering with the amplifier
   11.29. The pump of the amplifier of a steering
   11.30. The spherical hinge of steering draught
   11.31. Steering draught
   11.32. Corners of installation of wheels
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

11.25. The ignition lock CONTACT GROUP OF THE LOCK OF IGNITION

Removal

PERFORMANCE ORDER
1. Remove the negative plug from the accumulator.
2. Open a cover key колодки and disconnect an electric socket. Turn on 90 a clip and uncover boxes with fuses. Unscrew screws of fastening and remove the bottom furnish of the panel of devices.
3. Unscrew screws of fastening of the bottom casing of a steering column and remove the top and bottom casings from a column.
4. Insert a key into the lock of ignition and turn it in the first position. Shift скобу fastenings, return a key in non-working position and take it from the ignition lock.
5. Remove скобу fastenings of contact group of the ignition lock.
6. Take contact group from a back part of the case of the lock of ignition.
7. Disconnect the electric socket located on wires of contact group of the lock of ignition.

Installation

PERFORMANCE ORDER
1. Before installation combine apertures in the centre of contact group with the lock cylinder. In connection with the asymmetrical form of an operating pin of the cylinder of the lock the contact group can be established only in one position.
2. Establish contact group of the lock of ignition in its back part and fix скобой.
3. Turn a key in the ignition lock in the first position so that the lock cylinder was completely combined with the case. Move скобу fastenings into place and check up work of the lock of ignition.
4. Connect an electric socket of contact group of the lock of ignition to the main plait of wires.
5. The further installation is made in sequence, return to removal.

THE CYLINDER OF THE LOCK OF IGNITION

Cнятие

PERFORMANCE ORDER
1. Remove contact group of the lock of ignition.
2. Put forward the cylinder of the lock of ignition from the case, marking an arrangement of the lock of a steering column. Uncover the lock cylinder.
3. Pay attention to an arrangement of adjusting pins in the case of the lock of ignition and if necessary take them.

Installation


PERFORMANCE ORDER
1. Combine the lock of a steering column with the cylinder of the lock of ignition and establish a decorative cover on the cylinder of the lock of ignition. Check up that adjusting pins are on the place in the case of the lock of ignition. Establish the cylinder of the lock of ignition in gathering in the case. Thus combine the lock of a steering column with a groove in the case.
2. Establish contact group of the lock of ignition.

THE IGNITION LOCK

The prevention

At installation of the lock of ignition it is necessary to use new cut off bolts.


Cнятие

PERFORMANCE ORDER
1. Remove the negative plug from the accumulator. Remove a steering wheel.
2. Disconnect an electric socket of contact group of the lock of ignition from the main plait of wires.
3. Using a hammer and выколотку (punch), unscrew cut off bolts of fastening of the lock of ignition (are specified by arrows), tapping on their edges выколоткой round an axis until they cannot be unscrewed a hand. Unscrew bolts completely and remove the lock of ignition from a steering column.

Installation

PERFORMANCE ORDER
1. Will put the ignition lock on a steering column and fix new cut off bolts.
2. In regular intervals and gradually tighten cut off bolts until they will not be slightly tightened. Check up working capacity of the lock of ignition then tighten each bolt so that the bolt head was cut off.
3. Connect an electric socket of the lock of ignition to the main plait of wires.






Читаем здесь: https://welx.net