Peugeot 406

Since 1996 of release

Repair and car operation



Peugeot 406
+ 1. The maintenance instruction
+ 2. Maintenance service
+ 3. The engine
+ 4. Systems of cooling, heating and ventilation
+ 5. Fuel system
+ 6. Ignition system
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. A suspension bracket and a steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward bearings of a nave
   11.4. A forward rack
   11.5. Repair of a forward rack
   11.6. The bottom lever of a forward suspension bracket
   11.7. The bottom spherical hinge of a forward suspension bracket
   11.8. The stabilizer of cross-section stability of a forward suspension bracket
   11.9. A side scene of the stabilizer of cross-section stability of a forward suspension bracket
   11.10. The bottom frame of a forward suspension bracket
   11.11. A nave of a back wheel
   11.12. Replacement of bearings of a back nave
   11.13. The shock-absorber of a back suspension bracket
   11.14. A cylindrical spring of a back suspension bracket
   11.15. A pin of a nave of a back suspension bracket
   11.16. The bottom lever of a back suspension bracket
   11.17. The top lever of a back suspension bracket
   11.18. The directing lever of a back suspension bracket
   11.19. Draught of a back suspension bracket
   11.20. The stabilizer of cross-section stability of a back suspension bracket
   11.21. A side scene of the stabilizer of cross-section stability of a back suspension bracket
   11.22. A steering wheel
   11.23. A steering column
   11.24. An intermediate shaft of a steering column
   11.25. The ignition lock
   11.26. The steering mechanism
   11.27. Replacement of protective covers of the steering mechanism
   11.28. Removal of air from system of a steering with the amplifier
   11.29. The pump of the amplifier of a steering
   11.30. The spherical hinge of steering draught
   11.31. Steering draught
   11.32. Corners of installation of wheels
+ 12. A body
+ 13. An electric equipment
+ 14. The basic malfunctions

11.14. A cylindrical spring of a back suspension bracket

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and fix on supports. Remove a corresponding back wheel.
2. Establish under the external end of the back bottom lever a jack and raise the lever so that the spring has been slightly compressed.
3. Unscrew external шарнирный a lever bolt (it is specified by an arrow).
4. Unscrew a nut from internal шарнирного a lever bolt.
5. Unscrew the bottom bolt of fastening of the back shock-absorber.
6. Disconnect tubes of brake system and electric wires from скоб fastenings on the bottom lever.
7. Slowly lower a jack to a spring outright release. Remove a spring together with its top and bottom nests.
8. Check up a spring condition.

Installation

PERFORMANCE ORDER
1. Establish the bottom and top nests of a spring on the places. Grease a rod of the shock-absorber and a place of fastening of the bottom part of the shock-absorber with greasing Molykote G Rapide Plus.
2. Establish a spring into place and by means of a jack lift the lever, checking, that the spring ends correctly became in nests.
3. Combine the bottom lever with a nave and insert external шарнирный a bolt. Screw on internal and external шарнирные bolts new nuts, tightening them by hand.
4. Combine the bottom part of the shock-absorber with the bottom lever, insert a bolt of fastening and screw on it a new nut by hand.
5. Lower a jack and release the bottom lever. Fix on the bottom lever brake tubes and electric wires скобами fastenings.
6. Establish a back wheel and lower the car. Shake the car that suspension bracket elements have risen on the places. Tighten nuts the demanded moment.